2022年2月11日金曜日

完成したJBL 4425 & JBL 3145ネットワーク作業 Assembled JBL 4425 & JBL 3145 crossover work


こちらは最近ブログで作業を紹介していたJBL 4425です。ついに組みあがりました。これから代表による音質チェックを行い、アッテネータープレートを貼りつけて、周波数特性を測定します。
This is the JBL 4425 I have been posting about lately. They have been assembled so now our president Hosoi will check it's sound quality, attach the attenuator plate, and take the frequency characteristic data.


この写真は現在作業中のJBL 3145ネットワークです。セレクタースイッチの取付が完了しました。これからコンデンサーや抵抗を基板上の信号が流れを確認しながら良音質方向に取り付けます。一つでも間違えると音質に大きな影響を及ぼしますので細心の注意が必要です。
This is the JBL 3145 crossover that I have been working on lately. The rotary switch has been placed and now I will place the capacitors, resistors, and coils according to the better sounding polarity. This procedure is important, since one single mistake in the polarity will affect the sound massively.


LF,MFフィルターに使用するパーツの取付が完了しました。次はHF,UHFフィルターのパーツを取り付けます。
I have place the parts for the LF and MF filters. Next I will place the HF and UHF filter parts.



HF,UHFフィルターのパーツ取付が終わりました。これから配線を取り付けて、アッテネーターの交換作業に入ります。
I have placed the HF and UHF filter parts. Now I will finish with the wiring and replace the attenuators.

2022年2月9日水曜日

JBL 2245H カプトンボビン化、JBL 435Al修理、ステンレスホーンの入荷 JBL 2245H Kapton former voice coil replacement, JBL 435Al repair work, and horns for the 075 etc. has restocked


この写真は修理が完了したJBL 2245Hです。今回は当社オリジナルクロスエッジ交換、ダンパー交換、マグネット反転着磁、そしてボイスコイルをアルミボビンからカプトンボビンのものへと換装しました。カプトンボビンボイスコイルに変えることによってアルミボビンの影響で生じるダンピングを抑えることができ、より低域を豊かに鳴らすことが可能となります。詳しくはこちらの記事をご参照ください。
The repair work has been finished on this JBL 2245H. We have replaced the surrounds to our original cloth material, changed the spider, reversed the magnet's polarity, and have changed the voice coil to one with a Kapton former(from one with  an aluminum former). By changing the former material from aluminum to Kapton, the damping effects will be reduced and make it possible to produce richer bass sounds. Details here.


こちらの写真は修理が完了したJBL 435Alです。今回施した作業は磁性流体の除去、ボイスコイルの断線修理、バックチャンバー吸音材交換およびダイアフラムセンター出し再調整です。
This is a JBL 435Al that has been repaired. We have removed the magnetic fluid, repaired the disconnected voice coil, replaced the chamber wadding, and have re-centered the diaphragm.


075や2402などで使用するステンレスホーンが入荷しましたので検品作業を行っています。以下、商品ページのリンクです。
http://jbl43.com/?pid=12738210

We have restocked the horns for the JBL 075, 2402 etc. Below is the link to the product page.
http://jbl43.com/?pid=12738210

JBL 3145ネットワークアップグレード作業、JBL C36 Viscount完成 Upgrading the JBL 3145 crossovers and the JBL C36 Viscount completed


こちらの写真はパーツを全て取り外したJBL 3145ネットワーク基板です。これからテフロン銀メッキ線へと配線交換する作業に必要な加工を施します。
These are the JBL 3145 circuit boards after all the parts have been removed. I will now process them in order to change the wires to Teflon silver plated wires.


これは背面端子板です。背面板を加工して、大型金メッキ端子へと交換しました。
This is the rear binding post panel. I have changed the binding posts to large sized gold plated terminals.


この写真は使用するロシアンミリタリースペックのロータリースイッチです。
詳しくはこちら
This is the Russian military spec rotary switch we will be using for the above crossover.
Details here.


JBL C36 Viscountが組みあがりました。ネットワークの仕様は以下の通りです。

【D130 + 075用 ネットワーク使用パーツ】
・ファインメットカットコアコイル(高域フィルター用)
・Mundorf Mcap EVO SilverGold Oil コンデンサー
・トランス式アッテネーター
・背面大型金メッキ端子
・テフロン銀メッキ線

The JBL C36 Viscount has been completed. Below are the specifications for the installed crossovers.

[ D130 + 075 crossovers ]
*Finemet cut core coil for the high frequency filter
*Mundorf Mcap EVO SilverGold Oil capacitors
*Transformer type attenuator
*Gold terminals
*Teflon silver plated wires

2022年2月8日火曜日

完成!モノラル仕様1本 JBLヴァイカウント・ケンリックサウンド新品リプロダクト 芯がある太い音 Monaural Version Newly Built JBL C36 Viscount



完成しました!お客様からのオーダーで製作しましたモノラル仕様1本のJBLヴァイカウント・ケンリックサウンド新品リプロダクトです。1本とは思えないほどの芯がある太い音を動画でご確認ください。

JBL 4425用ドライバーダイアフラムアップグレード削り出し無垢バックカバー ケンリックサウンド音の良さの秘密 JBL 2416H Diaphragm Replace & Solid Chamber



JBL 4425用のドライバーである、JBL 2416Hのダイアフラムアップグレードに関する動画です。チタン素材ダイヤモンドエッジダイアフラムから、アルミ素材タンジェンシャルダイアフラムへ交換すると同時に、当社オリジナルの削り出し無垢バックカバーを装着して、抜群に良い音を引き出す方法を紹介しています。

ドライバーダイアフラム調整+真円出し+ステンレス無垢バブルバックカバー ケンリックサウンド音の良さの秘密 JBL LE85 Diaphragm Adjusting SUS Humpback Cover



コンプレッションドライバー調整において最も大切なことの一つである、ダイアフラム真円出しについてと、当社オリジナルであるJBL LE175, LE275, LE85, 2420,2421用のステンレス無垢バブルバックカバーの紹介です。

2022年2月7日月曜日

JBL D131リコーン作業、JBL 2214Hクロスエッジ交換、そしてJBL C36 Viscount ネットワーク取付完了 JBL D131 re-coning, JBL 2214H cloth surround replacement, and JBL C36 Viscount crossover installation


これは現在作業中のJBL 4312MK2に使用するJBL D131の様子です。コーンのアセンブリーを終えて、エッジを接着して、ボイスコイルのセンター出し作業を行っているところです。
This is a JBL D131 that will be used for the JBL 4312MK2 we are building at the moment. The cone have been assembled and is being attached to the frame, while centering the voice coil position.


こちらの写真は近々完成予定のJBL 4425に使用するJBL 2214Hです。当社オリジナルのクロスエッジに交換を終え、ボイスコイルのセンター出しも完了しました。
This is a JBL 2214H that will be used for the JBL 4425 that will be completed soon. They have been changed to our original cloth surrounds, and the voice coil centering process has also finished.


これはJBL C36 Viscountです。全てのスピーカーユニットが揃ったので、ネットワークを組み込み、フィルター用コイルの最良取付ポジションのテストを行い、取り付け作業も完了しました。これから吸音材および全てのスピーカーユニットを取り付けて、代表の細井による最終音質チェックを行います。
All the speaker drivers have been made, the crossover installed, and the filter coil position test/installation has bee completed. We will now place the wadding material and the drivers, so our president Hosoi can proceed with the final sound check.

2022年2月5日土曜日

JBL 3145ネットワーク解体作業、厳重梱包されたJBL 4344MK2 Disassembling the JBL 3145 crossovers, and safely packed JBL 4344MK2s


こちらは解体を開始したJBL 3145ネットワークです。今回コンデンサーは交換しますが、抵抗やコイルは純正のものを使用しますので、取り外す際にはダメージを与えないように気を付けなくてはいけません。
These are JBL 3145 crossovers that are being disassembled. This time we will be replacing the capacitors, but will be using the original resistors and coils, so you have to be extra careful not to damage them while doing this.
分解が完了しましたので、全てのパーツを一度取り外します。
I have finished disassembling the circuit board, so I will now take remove all the parts.


これは今回使用するパーツです。コンデンサーと使用する純正パーツは取り付ける前に代表の細井によって良音質方向を確認してもらい、結果に準じて基板に取り付けます。
These are the new parts we will be using. Our president Hosoi will check the better sounding  polarity of the capacitors and the original parts before placing them on the circuit board.


この写真は本日出荷するJBL 4344MK2です。御覧の通り、専門業者による厳重梱包をしてありますので、安全に輸送することができます。
These are JBL 4344MK2s that will be shipped out today. As you can see, they have been packed safely so they will be delivered safely.

JBL 4312MK2 カスタムネットワーク&ウーファーD131リコーン作業、本日作業開始のJBL 4345用ネットワーク Custom crossovers and D131 woofer re-coning process for the JBL 4312MK2s, JBL 4345 crossover work



こちらの写真は現在作業中のJBL 4312MK2に使用するカスタムネットワークです。ほとんどの配線が終わりましたので、これからフィルター特性を測定します。問題がなければスピーカーキャビネットへの組み込みを開始します。
These are the custom crossovers for the JBL 4312MK2s we are building now. Most of the wiring has been finished, so I will test it's filter characteristics. If there are no problems, I will start to install them into the speaker cabinet.


これは同スピーカーに使用するJBL D131です。ケンリックサウンドオリジナルのコーン紙&クロスエッジを使用してリコーンをします。
This is the JBL D131 that will be used in the speakers mentioned above. It will be re-coned using Kenrick Sound's original cones and cloth surrounds.


こちらは本日作業を開始するJBL 4345用のJBL 3145ネットワークです。作業前の測定を行ってからネットワークの解体に入ります。今回のカスタム内容は配線交換、コンデンサー交換、セレクタースイッチ交換、端子交換、そしてアッテネーター交換と、かなりボリューム多めです。
These are JBL 4345 crossovers (JBL 3145) that I will start working on today. I will be taking it's data and then start to disassemble them. This time I will be changing the wires, capacitors, rotary switches,  terminals, and the attenuators.